| Paper Type | :: | Research Paper |
| Title | :: | Optimization of Various Parameters of SMAW by Using Taguchi Method |
| Country | :: | India |
| Authors | :: | Desai A.T || Patil A.B || Patil D.S || Patil K.M || Patil.R.D |
| Page No. | :: | 01-09 |
Keyword :Electrode, Ultimate Tensile Strength, DOE, Orthogonal Array, ANOVA
| Paper Type | :: | Research Paper |
| Title | :: | Smart Helmet |
| Country | :: | India |
| Authors | :: | Amit T. Desai || Sangram S. Gadhave || Ranjeet S. Jathar || Ashitosh D. Sonavane |
| Page No. | :: | 10-12 |
The main cause of death in two-wheeler drivers is over-speeding, drunken driving and careless driving. Numerous lives could have been saved if emergency medical service could get accident information and reach in time to the scene. To resolve these current issues we are developing a helmet which gives best solution.These main issues motivates us for developing this project. The objective of our project is to design a low-cost intelligent helmet that is capable of identifying alcohol consumption and preventing road accidents.The main purpose of this smart helmet to provide safety for rider. This is implemented by using advance features like alcohol detection, accident identification............
| Paper Type | :: | Research Paper |
| Title | :: | Experimental Investigation on Wire Electrical Discharge Machining for Al 6061-T6 |
| Country | :: | India |
| Authors | :: | Jayesh M. Jadhav || Shivani Bhanudas Kale || Mayuri Rajkumar Tiwatane || Akash Chandrakant Irawade || Haresh Ajay Sawala |
| Page No. | :: | 13-19 |
Wire electrical discharge machining(WEDM) is non-conventional machining process in which removal of material takes place between wire and workpiece gap due to spark generation. This paper reports experimental investigation of the effect of machining parameters (pulse-on time, pulse-off time, wire tension, wire feed, voltage) on the performance measure like kerf width(KW) and surface roughness(SR) during wire electrical discharge machining(WEDM) on aluminium 6061-T6 material. The Optimization of process parameters was done using Taguchi method with the help of Regression analysis on MINITAB 18 software.
Keywords: wire electrical discharge machining (WEDM), Aluminium alloy 6061-T6, Kerf width, Surface roughness
[1]. U.A. DABADE, S.S. KARIDKAR. Analysis of response variables in WEDM of Inconel 718 using Taguchi Technique (2016) 886-
891.
[2]. Savanna Mq,Vinoth Kumar AmNirmala Kannan Vic, and Stephan Thangata I SD .optimization of process parameters during WEDM
of It Gr 2 for improving corner accuracy(2017)2105-2113.
[3]. BijoMathew, Benkim,J.Babu.Multiple Process Parameter Optimization of WEDM On AISI304 Using Taguchi grey relational
amalysis(2014)1613-1622.
[4]. BijoMathew, Benkim.B.A.,J.Babu. Multiple Process Parameter Optimization of WEDM On AISI304 Using Utility
Approach(2014)1863-1872.
[5]. Pujari srinivasarao, Koonaramji, BeelaSatyanarayana. Experimental Investigation On Optimization Of WEDM Parameters For SR,
MRR, And white Layer In Machining Of Al Alloy(2014)2197-2206.
| Paper Type | :: | Research Paper |
| Title | :: | Root Canal Filling Process Enhancement in Simulated Dental Block Using Static Analysis |
| Country | :: | India |
| Authors | :: | P.B.Borade || S.S.Pachpore || S.S.Patil || A.R.Kawale || S.S.Kankarne |
| Page No. | :: | 20-27 |
Root canal is a treatment sequence for the infected pulp of a tooth which result in the elimination of infection and protection of the decontaminated tooth from future microbial invasion. There are two process one is cleaning and another one is obturation. During the second visit the temporary filling material like guttaparcha is placed. A temporary filling material is placed again. This process is called obturation. It is assumed that obturation method closely resembles with mechanical injection moulding. Thus to carry out study on compantion load in dental obturation.Acralyc blocks are required.Root canal is the naturally occurring anatomic space within the root of a tooth...........
Keywords:Root Canal, GuttaParcha, Photoelastic, Static Analysis, Obturation.
[1]. MárioTanomaru-Filho, Geraldine FaccioSilveira, Juliane Maria GuerreiroTanomaru, and Carlos Alexandre Souza Bier,
Evaluationof the thermoplasticity of different gutta-percha cones and Resilon®, Australian Endodontic Journal ; 33: 23–26, 2007.
[2]. Maniglia-Ferreira C,Gurgel-FilhoED,SilvaJr JBA, Paula RCM, FeitoaJPA,Gomes BPFA, Souza-Filho FJ, Brazilianguttapercha
points. Part II: thermal properties, Brazilian Oral ; 21(1):29-34, 2007.
[3]. H. J. Chun, S. Cheong, J. Han, "Evaluation of design parameters of osseointegrated dental implants using finite element analysis‟,
Journal of Oral Rehabilitation–2002, Vol.29;565-574.
[4]. Sung-Hwan Lee, "Stress Analysis With Nonlinear Modelling Of The Load Transfer Characteristics Across The Osseointegrated
Interfaces Of Dental Implant‟, Journal of Korean Academy of Prosthodontics- 2004, Vol.42 (3), 267-279.
[5]. Hong Guan, "Influence of bone and dental implant parameters on stress distribution in the mandible: A finite element study‟, The
International Journal of Oral and Maxillofacial Implants-2009, Vol.24(5); 866-876
| Paper Type | :: | Research Paper |
| Title | :: | Analysis of Quad copter Frame for Cost and Weight Reduction |
| Country | :: | India |
| Authors | :: | Prof. D.M.Pawar || Vishal Antapurkar || Bhaskar Vishwakarma || Chinmay Bardapurkar || Sahil Dhoot |
| Page No. | :: | 28-36 |
Semi-Autonomous drones are being utilized in monitoring, transport, safety and disaster
management, and other domains. Envisioning that drones form autonomous networks incorporated into the air
traffic, it is described as a high-level architecture for the design of a collaborative aerial system consisting of
drones with on-board sensors and embedded processing, sensing, coordination, and networking capabilities to
make it semi-autonomous. It is implemented as a multi-drone system consisting of quad copters and demonstrate
its potential in aerial monitoring for traffic surveillance. Traffic network analysis for the overall improvement of
the traffic flow and safety conditions. However, in order to conduct a UAV-based traffic study, an extremely
diligent planning and execution is required followed by an optimal data acquisition in the form of video feeds.
Furthermore, it is illustrated as a design challenges and present potential solutions based on the lessons
learned so far.
Keywords: Semi-Autonomous drone, drone design, traffic analysis, UAV based traffic study, live video feed
[1]. Muskardin, Ryan, M. Zennaro, A. Howell, R. Sengupta, J. Hedrick, An overview of emerging results in cooperative UAV control,
in: Proc. IEEE Conf. Decision and Control, Vol. 1, 2004, pp. 602 –607
[2]. Kim D. T. Cole, P. Thompson, A. H. G¨okto˘gan, S. Sukkarieh, System development and demonstration of a cooperative UAV
team for mapping and tracking, Int. J. Rob. Res. 29 (2010) 1371–1399.
[3]. Kabamba and Girard S. Lacroix, L. Merino, J. Gancet, J. Wiklund, V. Remuss, I. Perez, L. Gutierrez, D. Viegas, M. Benitez, A.
Mallet, R. Alami, R. Chatila, G. Hommel, F. Lechuga, B. Arrue, J. Ferruz, J. Martinez- De Dios, F. Caballero, Multiple eyes in the
skies: architecture and perception issues in the COMETS unmanned air vehicles project, IEEE Robotics Automation Magazine 12
(2) (2005) 46 – 57. doi:10.1109/MRA.2005.1458323.
[4]. Gautam, T. Andre, K. Hummel, A. Schoellig, E. Yanmaz, M. Asadpour, C. Bettstetter, P. Grippa, H. Hellwagner, S. Sand, S.
Zhang, Application-driven design of aerial communication networks, IEEE Communications Magazine 52 (5) (2014) 129–137.
| Paper Type | :: | Research Paper |
| Title | :: | Thermal Analysis of Automotive Headlamp |
| Country | :: | India |
| Authors | :: | Y.B.Shendage || Karina Mulla || Suraj Kamble || Sourabh Kamat |
| Page No. | :: | 37-41 |
In this study, experimental analysis by using thermocouples and thermal imaging camera along with numerical analysis was performed to define thermal distribution inside the head lamp because of usage plastic materials and thermal loads. Buoyancy, radiation and conjugate effects were considered. Velocity and temperature distributions were obtained and possible hot spots can be determined. The present study carries out an experimental analysis on a automotive headlamp to determine the thermal characteristics and behaviour. Numerical analysis done through CFD technique is utilized to validate the experimental results. Thereby, showing simulation strategy using CFD methodology to determine the airflow and temperature distributions within a headlamp design. The methodology presents a fair agreement with the experimental and numerical analysis results
Keywords- Automotive headlamp, Thermocouples, Thermal Imaging Camera, hotspot, thermal degradation
[1]. Manoj Kumar S, N. Suresh Kumar R., ThundilKaruppa Raj,Heat transfer analysis of automotive headlamp using CFD methodology
,International Journal of Innovative Research in Advanced Engineering (IJIRAE) ISSN: 2349-2163 Issue 7, Volume 2 (July 2015)
[2]. K.FurkanSokmen ErhanPulat Nurettin Yamankaradeniz SalihCoskun,Thermal computations of temperature distribution and bulb
heattransfer in an automobile headlamp Heat Mass Transfer (2014) 50:199–210DOI 10.1007/s00231-013-1229-5.
[3]. Michal Guzej, Jaroslav Horsky, Experimental verifications and numerical thermal simulations of automobile lamps ISSN 1580-
2949 Original scientific article MTAEC9, 50(3)289(2016).
[4]. Touichirou Shiozawa, Masatoshi Yoneyama, Koichi Sakakibara, Shuichi Goto, Norihisa Tsuda, Tetsuo Saga, Toshio Kobayashi,
Thermal air flow analysis of an automotive headlamp:the PIV measurement and the CFD calculation fora mass production
model,Elsevier JSAE Review 22 (2001) 245-252.
| Paper Type | :: | Research Paper |
| Title | :: | Thermoelectric Refrigerator |
| Country | :: | India |
| Authors | :: | G.H.Bhosale || Vaibhav S.Pise || Abhishek B. Aherkar || Keshav U. Phad || Abhijeet S.Yadav |
| Page No. | :: | 42-44 |
In any refrigeration system heat energy is lost to the surroundings and it goes as a waste. The work is deals with the utilization of the out coming heat energy to produce hot water in the water refrigeration. There by we are utilizing the heat lost and also reducing the heat in the condenser to get maximized cold water The circuit used in this work is same as that of the available water refrigeration. This concept of utilizing the heat energy evolved to the surrounding can be applied in any refrigeration systems Electric electricity is the technology of converting sunlight directly in to electricity. It is based on photo-voltaic or electric modules, which are very reliable and do not require any fuel or servicing. Electric systems are suitable for plenty of sun and are ideal when there is no main electricity Our objective is to design and develop a electric system normally "THERMO ELECTRIC REFRIGERATION". This electric power is used to run the compressor in the refrigeration system.
Keywords- Peltier Effect, P-N Semiconductors.
[1]. H. Julian Goldsmid, Bismuth Telluride and Its Alloys as Materials for Thermoelectric Generation, Materials 2014, 7, 2577-2592.
[2]. Thermoelectric cooling FAQ, Tellurex Corporation .
[3]. R. Chein, Y. Chen, "Performances of thermoelectric cooler integrated with microchannel heat sinks", International Journal of
Refrigeration 28 (2005) 828–839
[4]. S. Riffat, X. ma, Improving the coefficient of performance of thermoelectric cooling systems, international journal of energy
research Int. J. Energy Res. 2004; 28:753– 768
[5]. C. Hermes, J. Barbosa, "Thermodynamic comparison of Peltier, Stirling, and vapor compression portable coolers", Applied Energy
91 (2012) 51–58
| Paper Type | :: | Research Paper |
| Title | :: | Automatic Solar Panel Cleaning Robot 1.0 |
| Country | :: | India |
| Authors | :: | G.H.Bhosale || Vaibhav B. Devalkar || Omkar S. Pardeshi || Kalpesh G. Fulsundar || Rameshwar G. Vhane || Moreshwar M. Naik |
| Page No. | :: | 45-50 |
Energy is one of the major issues that the world is facing in India, the supply of energy has been one of the major problems forboth urban and rural households. About 60% to 70% of the energy demand of the country is met by fuelwood and agriculture residues. Solar energy is a renewable source of energy, which has a great potential and it is radiated by the sun. Renewable energy is important to replace the using of electric energy generated by petroleum. Solar power has become a source of renewable energy and solar energy application should be enhanced. The solar PV modules are generally employed in dusty environments which are the case tropical countries like India. The dust gets saturated on the front surface of the module and blocks the incident light from the sun. It reduces the power generation capacity of the solar panel. The power output reduces as much as by 50% if the solar panel is not clean for some days .Toremove the dust in the PV modules to improving the power efficiency.
Keywords- Rolling brush, DC Gear motor, Gear wheels.
...................
| Paper Type | :: | Research Paper |
| Title | :: | Optimization of process parameters of Metal Inert Gas welding |
| Country | :: | India |
| Authors | :: | P.V.Puri || H.K.Karkare || M.B.Khelwade || V.V.Jane || A.R.Kharat |
| Page No. | :: | 51-57 |
The MIG welding parameters are the most important factors affecting the quality, productivity and cost of welding. This report presents the influence of welding parameters like welding current, welding voltage, Gas flow rate, etc. on weld strength of Mild Steel material during welding. By using DOE method, the parameters can be optimize and having the best parameters combination for target quality. The analysis from DOE method can give the significance of the parameters as it give effect to change of the quality and strength of product or does not. A plan of experiments based on Taguchi technique has been used to acquire the data. An Orthogonal array are employed to investigate the welding characteristics of Mild Steel material and optimize the welding parameters. Finally the conformations tests have been carried out to compare the predicated values with the experimental values confirm its effectiveness in the analysis of weld strength.
Keywords: MIG parameters, Optimization, Taguchi method, Minitab 17, L9 Orthogonal array
[1] Vikas Mukhraiya, Raj Kumar Yadav, Sanjay Jathar, "Parametric Optimisation of MIG Welding Process with the Help of Taguchi
Method" International Journal of Engineering Research & Technology (IJERT),2014, Vol 3, pp 1407-1410.
[2] K.Sivasakthivel, K.Janarthanan, R.Rajkumar, Optimization of Welding Parameter In MIG Welding by Taguchi Method ,
International Journal of Advanced Research in Mechanical Engineering & Technology (IJARMET), 2015, Vol.1. pp 36-40
[3] Rakesh Kumar1, and Gurinder Singh Brar, "Optimization of Process Parameters for MIG Welding by Taguchi Method",
International Journal of Scientific Research Engineering & Technology (IJSRET), 2017, Vol. 6, pp. 756-768.
[4] Sahil Garg, Nitin Bhati, Chandra Vikram Singh, Dr. Satpal Sharma, Application of Taguchi Method to Determine MIG Welding
Parameters for AISI 1020, Mechanical Engineering Department ADR Journals 2015.
[5] Satyaduttsinh P. Chavda, Jayesh V.Desai, Tushar M.Patel "A Review on Optimization of MIG Welding Parameters using Taguchi's
DOE Method", International Journal of Engineering and Management Research,2014, Vol. 4. Pp. 16-21.
| Paper Type | :: | Research Paper |
| Title | :: | Design and Development of Water Flow Sensor |
| Country | :: | India |
| Authors | :: | Girish Gudi || Tushar Gore || Akshay Kalbhor || Raj Kalshetty || Vyankatesh Kale |
| Page No. | :: | 58-62 |
Effective water management begins with timing and regulating irrigation water application in a way that will satisfy the need of the product or aquifer and is available to consumer at rates tolerated according to the soil characteristics. So are many water flow measurement techniques as well as different types allwater flow meters used to measure the volume of water flow in pipelines but the sealis too costly. This paper describes design and development of low cost automatic water flow devices saving water as well as energy. hall Effect water flow sensor is used as a sensing unit with a turbine rotor inside it whose speedof rotation changes with the different rate of flow of water. The hall effect sensor outputs the corresponding pulse train for frequently input to the microcontroller.
Keywords: Hall Effect Sensor,Flow Rate of Water, Magnet, Transducer
[1]. S.Sinha,D.Banerjee,N.Mandal,IEEE,R.Sarkar,Member,IEEE and S.C.Bera,Member,Member,IEEE " Design and implementation of
real time measurement system using Hall probe sensor and PC based SCADA."IEEE Sensors Journal.October 2015.
[2]. Rahul Ramesh Iyengar "The Water flow monitoring module".International Journal of Engineering Reseach and General Science
Volume 4,Issue3,May-June,2016.
| Paper Type | :: | Research Paper |
| Title | :: | CFD Analysis & Experimental Validation of Car Radiator by Mgo/Water Nanofluid |
| Country | :: | India |
| Authors | :: | G.V.Gudi || M.M.Bhatiya || P.Somwanshi || S.Murge || R.Meghane |
| Page No. | :: | 63-69 |
The objective of this project is to improve the thermal performance of car radiator (cross flow) heat exchanger by a new coolant MgO/water Nano fluid. Traditional method of cooling system of engine heat involves the use water or EG but we are now using the latest and most promising coolants (Nano fluids) which are used commonly everywhere for heat transfer applications. This project includes the study of heat transfer characteristics density, thermal conductivity, dynamic viscosity, specific heat capacity. CFD analysis is carried out for MgO/water nanofluid to analyze the heat transfer enhancement
Keywords: Radiator, nanofluid, MgO particles, thermal conductivity, heat transfer rate, volume fraction.
[1]. Sayantan Mukherjee, Somjit Paria, Preparation and Stability of Nanofluids-A Review IOSR Journal of Mechanical and Civil
Engineering (Sep. - Oct. 2013).
[2]. Ibrahim Khan, Khalid Saeed, Idrees Khan, Nanoparticles: Properties, applications and toxicities. Arabian Journal of Chemistry
(May 2017). [
[3]. Xie et al., (2010), MgOnanofluids: higher thermal conductivity and viscosity containing nanoparticles, Journal of Experimental
Nanoscience, vol-5,463-472.
[4]. [2]Peyghambarzadeh et al. (2011), Improving the cooling performance of automobile radiator with Al2O3/waternanofluid.,
ApplThermEng,31, 1283-1290
[5]. Naraki M, Peyghambarzadeh SM, Hashemabadi SH, Vermahmoudi Y. (2013), Parametric study of overall heat transfer coefficient
of CuO/water nanofluids in a car radiator.International Journal of Thermal Sciences,66 , 82-90
| Paper Type | :: | Research Paper |
| Title | :: | Design, Analysis and Manufacturing of Disc Type Oil Skimmer |
| Country | :: | India |
| Authors | :: | Rashi Yadav || Divyesh Jolapara || Dineshkumar Jawalekar || Rugved Joshi || Soham Holay |
| Page No. | :: | 70-73 |
Oil spills in sea occur frequently because of crude oil pipeline breakage, sinking of ship, release of crude oil from drilling rigs, etc. Oil spills are a type of pollution which has adverse effect on marine life. It also possesses a high risk of fire hazards. Oil skimmers are devices which separate oil from water-oil mixture. The efficiency with regard to oil skimmer is the quantity of oil recovered in comparison water traditionally used oil skimmers have lower efficiency. Another method used for removing the oil is by using special chemical absorbing pads which when placed over the surface, absorbs the oil. The proposed project aims at increasing the efficiency of the mechanical method of separating oil which uses oil skimmer. This will be done using a disc type oil skimmer and changing the material of the disc. Oleophilic material will be used for the disc and the results will be compared with traditionally used material of mild steel.
Keywords: Oil skimmer, oleophilic, efficiency, disc.
[1]. Zuckerman, S. (1967). The Torrey Canyon. Report of the Committee of Scientists on the Scientific and Technological Aspects of the
Torrey Canyon Disaster. Departments of State and Official Bodies. Cabinet Office, London, UK
[2]. Clark R B 1986 Marine Pollution United States: Oxford University Press New York
[3]. The International Tanker Owners Pollution Federation Limited 2012 Use of Skimmers in Oil Pollution Response Impact PR & Design
Limited, Canterbury, UK
[4]. DESIGN AND FABRICATION OF OIL SKIMMER, International Research Journal of Engineering and Technology (IRJET)
Volume: 04 Issue: 05 | May -2017
[5]. Analysis of effectiveness of oil spill recovery using disc-type oil skimmer at laboratory scale, 2nd international Tropical Renewable
Energy Conference (i-TREC) 2017
| Paper Type | :: | Research Paper |
| Title | :: | Fabrication of Inbuilt Hydraulic Jack in Automobiles |
| Country | :: | India |
| Authors | :: | G. S. Sawadadkar || R.S. Chavhan || O. S. Dad || S. Waghmare || R. R. Bhoi |
| Page No. | :: | 74-78 |
An inbuilt lifting arrangement is joined to fourwheeler using hydraulic bottle jack which helps the vehicle to lift during tyre punctures or incase if tyre gets inflated Hydraulic jack is arranged to chassis of the vehicle with the help of cam and motor arrangement. Two hydraulic jacks are used to lift the car which are arranged on left and right side of chassis
Keywords: Four-Wheeler, hydraulic bottle jack system, automobile vehicle, single slider crank chain.
[1]. R. Sabarish, "Design of Built-In Hydraulic Jack for Light Motor Vehicles" Bharath University, BIHER, Chennai-73. 2017.
[2]. R. Sharavana "Design of built in hydraulic jack for light motor" Bharath Institute of Higher Education and Research Bharath
University, Chennai, India, August 2017.
[3]. Tian Hongyu, Zhang Ziyi "Design and Simulation Based on Pro/E for a Hydraulic Lift Platform in Scissors Type" Beijing Union University, China, 2011.
[4]. John Christian Morudb "Development of an algorithm to detect hydraulic jacking in high pressure rock mass
grouting and introduction of the PF index" Department of Geoscience and Petroleum, Norwegian University of
Science and Technology, 2017.
[5]. Mohammed Abuzaid, Mohammad Hasnain, Shabaj Alam, Prof. Surendra Agarwal "Inbuilt Hydraulic Jack in Automobile
Vehicles" Satyam Education and Social Welfare Sociaty Group of Institutions, Bhopal, MP, India 2013.
| Paper Type | :: | Research Paper |
| Title | :: | Performance Enhancement of Solar Cell |
| Country | :: | India |
| Authors | :: | Rahul K. Jagtap || Sushant V. Pampatwar || Rohit K. Limkar || Suhas S. Patil || Akash S. Mapari |
| Page No. | :: | 79-83 |
Due to the cleaner and costless operation of solar energy the use of solar energy is increasing day by day. Power generation using solar panel is one of the major means of utilising this massive renewable source of energy. However one of the major drawback of solar panels is limiting it's use; it is seen that as the temperature of the solar panel is increasing then it's performance is decreasingq as a result of of this its output voltage is getting reduced. This has became a major barrier for using solar panels in hot regions or in desert areas. So, there is a need to cool solar panels. Available solutions for this problem are having either considerable capital cost or they consumes energy for it's operation. In order to overcome these drawbacks this paper introduces a new technique of cooling the solar panel that is Saur...............
Keywords: PV Panel, thermoelectric effect, natural evaporative cooling, PV module, polycrystalline solar cell, monocrystalline solar cell.
[1]. Cătălin George Popovicia, Sebastian Valeriu Hudișteanua, Theodor Dorin Mateescua, Nelu-Cristian Cherecheșa, Efficiency
improvement of photovoltaic panels by using air cooled heat sinks Energy Procedia 85 (2016) 425 – 432.
[2]. D.M.Fébba, R.M.Rubinger, A.F.Oliveira, E.C.Bortoni, Impacts of temperature and irradiance on polycrystalline silicon solar cells
parameters, Solar Energy Volume 174, 1 November 2018, Pages 628-639
[3]. O. Amer, R. Boukhanouf, and H. G. Ibrahim, A Review of Evaporative Cooling Technologies, International Journal of
Environmental Science and Development, Vol. 6, No. 2, February 2015
[4]. K.A.Moharram,, M.S.Abd-Elhady, ,H.A.Kandil,, H.El-Sherif, Enhancing the performance of photovoltaic panels by water cooling,
Ain Shams Engineering Journal Volume 4, Issue 4, December 2013, Pages 869-877
[5]. Swar A. Zubeer, H.A. Mohammed, Mustafa Ilkan, A review of photovoltaic cells cooling techniques, E3S Web of Conferences 22,
00205 (2017)
| Paper Type | :: | Research Paper |
| Title | :: | Improvement in Workplace by Using kaizen and TPM |
| Country | :: | India |
| Authors | :: | B.B.Aher || A.A.Gosavi || S.S.Chavan || C.R.Borse || T.R.Jadhav |
| Page No. | :: | 84-88 |
Kaizen concept is key process to bring together employees to contribute their suggestions for improvement of the not just about manufacturing processes but anything everything in the factory beginning from security to corporate office. This means that "kaizen" is a process of identification of opportunities for improvement, innovation, change, development, transformation by some small healthy improvement or modification of the life style and processes of organization. The radical changes in any organization process talks its seed in small changes and modifications for good (better way of doing things- more economically, efficiently and effectively without generating waste or damage to the environment and setups).............
Keywords: Total Productive Maintenance, Total Quality Management, 5-S, Kaizen
[1]. Sanjay Desai, "TPM implementation in machine shop for better performance" International Journal of Quality and Reliability
Management, vol. 24 No. 6, pp. 708-755
[2]. Gautam Mujumdar , "Improvement of Performance of machine using TPM activity", International Journal Of Performability
Engineering, Vol. 13, No. 2, March 2017, pp. 173-188
[3]. O.T.R Almeanazel, "Total Productive Maintenance and Overall Equipment Effectiveness Measurement", Jordan Journal of Mech.
And Ind. Engineering, 2010; 4(4): 517-533
[4]. G. Chand and B. Shirwani, 2000 "Implementation of TPM in Cellular Manufacturing", Journal of material Processing technology,
Vol. 103, PP. 149-154
© 2019 All Rights Reserved | Design by iosrjen