International Conference on Innovation & Research in Engineering, Science & Technology (ICIREST-19)
(Volume-23)

Paper Type :: Research Paper
Title :: Review on The Study of FACTS Device SVC
Country :: India
Authors :: Minesh B. Jamunkar || Pankaj L. Baghele || Shubham G. Pachare || Tekchand R. lanjewar || Roshan M. Chahankar || Prof. R.R.Hete
Page No. :: 01-04

This paper describes the modeling and simulation of distribution SVC for the improvement of power transfer quality and maintains the voltage profile and power factor improvement. Voltage swag and swell is one of the major problem in power system stability studies because it reduce the voltage profile and makes the system unbalanced. Therefore, the main aim or consideration of this project is to maintain the voltage profile and the mitigation of power quality problems in transmission and distribution system. SVC is one of the shunt connected FACTS controller device which is used for the compensation of power quality problem and maintains the voltage profile and improve power factor and it produces a greater advantages than compensators.

Keywords –Voltage profile,Transient Stability, SVC, PSS, MATLAB/Simulink

[1]. Tejinder Singh Saggu, Lakhwinder Singh, "Comparative Analysis of Custom Power Devices For Power Quality Improvement in Non-linear Loads" proceedings of 2015 RAECS UIET Pnjab University Chandigarh 21-22nd Dec 2015
[2]. M.V.Wankhede,V.K.Chandrakar, "Static Synchronous compensator (STATCOM) for the improvement of Electrical System Performance with Non-linear load", International journal of power systems.vol 1,pg. 27-32,2016..
[3]. Huang Shao-Ping, "Modeling and Simulating for Transient Stability Analysis of Power System using Dynamic Phasor" The 1stInternational Conference on Information Science and Engineering (ICISE2009).
[4]. Lin Xu, "Coordinated Control of SVC and PSS for Transient Stability Enhancement of Multi-Machine Power system" TELKOMNIKA, Vol. 11, No. 2, February 2013.
[5]. Devendra ManikraoHoley,Vinod Kumar Chandrakar, "Harmonic domain modeling of Space vector based 2203,2016


Paper Type :: Research Paper
Title :: Harnessing Maximum Energy From Biomass and Generation of Biogas
Country :: India
Authors :: Dr. S.P.Adhau || Akanksha Yawalkar || Swati Kodape || Ankita Padole || Anuja Hore || Vaishnavi Mawale || Karishma Dighore
Page No. :: 05-12

This paper represents how to harness the maximum energy from biomass and the production of biogas. Biogas Production requires anaerobic digestion. The anaerobic digestion of kitchen wastes produces biogas, a valuable energy resource. In Yeshwantrao Chavan College of Engineering, there are two canteens, and both having their own individual mess, where daily amount of kitchen waste is obtained which can be utilized for better purposes. In the campus of YCCE biogas plant for the production of biogas has been installed. For harnessing the maximum energy pre-digester tank in which any type of kitchen waste, manure etc........

Keywords: Biogas; Digeste Tankr; Predigester Tank; Kitchen Waste; Solar water Heater; Anaerobic Digestion

[1]. Rajendra Beedu and Pratik Modi, "Design of Bio Gas Generation Plant Based on Food Waste", Department of Mechanical and Manufacturing Engineering, Manipal Institute of Technology, Manipal University, Manipal, Karnataka, India Accepted 10 January 2014, Available online 01 February 2014
[2]. Navneeth & Kiran M Sannakki, "Comparative Study Of Biogas Production Using Kitchen Waste And Poultry Waste", Student, Department of Civil Engineering, Nagarjuna College of Engineering, Karnataka, India, June 2016
[3]. Aragaw T. and Andargie M. "Co-digestion of cattle manure with organic kitchen waste to increase biogas production using rumen fluid as inoculums", Int JPhys Sci, 8, 443-450 et al. (2013)
[4]. N.H.S.Ray, M.K.Mohanty and R.C. Mohanty, "Anaerobic Digestion Kitchen Waste: Biogas Production ,Purification and Application in I.C. Engines", Dept. of Mech Engg. CEB,BBSR,Odisha,India, Jan 2014


Paper Type :: Research Paper
Title :: Development Of Microcontroller Based Smart Egg Incubator System
Country :: India
Authors :: Vaishali Nandanwar || Moiz Ahmed || Sameer Barua || Prof. Dr. Sayyad Naimuddin || Anup Mahajan || Prof. Yasmin Sayeed
Page No. :: 13-17

The purpose of this project is to design and develop the system of an egg incubator that able to incubate various type of egg named as Smart Egg Incubator System for Various Types of Egg (SEIS). The SEIS will fill up with the temperature and humidity sensor that can measure the condition of the incubator and automatically change to the suitable condition for the egg. The health of egg is very important for the development of embryo within the egg. Improper control means that the temperature or humidity is too high or too low. In this project, the light heater is use to give the suitable temperature to the egg. By using the water and controlling fan, it is can make sure the humidity and ventilation in good condition. The status condition in the SIES will appear on the LCD screen display............

Keywords:Smart Egg Incubator System (SEIS), Aurdino, Incubator, Humidity, Temperature, Parameter monitoring.

[1]. Adhi Ksatria Theopaga, Achmad Rizal, Erwin Susanto," Design And Implementation Of Pid Control Based Baby Incubator", Journal of Theoretical and Applied Information Technology, Department of Electrical Engineering, Telkom University, Indonesia, pp. 19-24,Vol.70 No.1, 10th December 2014
[2]. Hitu Bansal, Dr. Lini Mathew, Ashish Gupta, "Controlling of Temperature and Humidity for an Infant Incubator Using Microcontroller", International Journal of Advanced Research in Electrical, Electronics and Instrumentation Engineering, Vol. 4, Issue 6, pp. 4975- 4982, June 2015, 2015.
[3]. Christina Tan, "Integrated Temperature, Light and Humidity Monitoring System for the Hospital Environment", Faculty of Electrical and Computer Engineering McMaster University, Hamilton, Ontario, Canada, 2010 . S.K. Mousavi, J. Ghobadi, M. Ghasem Nejad, " Incubator with Fuzzy Logic",University of Science and Technology, Faculty of Electric Engineering, Tehran, Iran, TJMCS Vol .5 No.3, pp. 197-204, 2012.
[4]. Sumardi Sadi, "Room Temperature Control System Prototype Industry Based Programmable Logic Controller Zelio SR2 B121 BD", Innovative Systems Design and Engineering, Vol.6, No.4, pp. 52-68, 2015."


Paper Type :: Research Paper
Title :: Arduino Based Dual Axis Sun Tracking Solar Panel Using LDR And Servo Motor
Country :: India
Authors :: Shaunak Manoj Narhekar || Aniket Suryakant Takale || Prof.Amardeep S. Potdar
Page No. :: 18-23

Solar tracking is now becoming very popular. Solar energy is rapidly advancing as an important means of renewable energy sources. "The solar tracking system is a method of generating electricity from sunlight." This method of generating electricity is simple and derived from natural resources. This only requires maximum sunlight. Design and construction of a solar tracking system that detects sunlight using LDR. The solar tracking loop is based on the Arduino-Atmel ATMega 328. It is programmed to detect sunlight through LDR and activate the servo motor to place the solar panel where it receives maximum sunlight. Compared to other motors, servomotors are more controllable, energy efficient, more stable, less expensive and more precise. The automatic tracking and implementation of solar energy can be significantly improved.

Keyward: Tracking, Servo Motor, Arduino-ATmega 328, Solar, Sun Tracking, MPPT

[1]. Sangamesh Malge, Kalyani Bhole, Ravi Narkhede, "Designing of Dual-axis Solar Tracking System with Remote Monitoring"2015 International Conference on Industrial Instrumentation and ontrol (ICIC) College of Engineering Pune, India. May 28-30, 2015
[2]. Anubhav Jain, Chinmay Jain, Member IEEE, Bhim Singh, Kamal-Al-Haddad and Ambrish Chandra, "A Dual Tangent Based Algorithm for Maximum Power Point Tracking of Solar PV Systems" IECON2015- YokohamaNovember 9-12, 2015, 978-1-4799-1762- 4/15/$31.00 ©2015 IEEE.
[3]. DjilaliChogueur*, Said Bentouba, AmraouiMerouane, "Smart Sun Tracking System"978-1-4673-7894- 9/15 (2015) IEEE.
[4]. Bashar K. Hammad, Rami H. Fouad, Moh'd Sami Ashhab, Salem D. Nijmeh,Mousa Mohsen, Asma Tamimi, "Adaptive Control of Solar Tracking System", The Institution of Engineering and Technology 2014.
[5]. Jyoti Mishra , Ritula Thakur, Alok Deep "Arduino based Dual Axis Smart Solar Tracker", International Journal of Advanced Engineering, Management and Science (IJAEMS), Vol-3, Issue-5, May- 2017.


Paper Type :: Research Paper
Title :: A Review Based Assessment of Solar Box-Type Cooker
Country :: India
Authors :: Aman Shrivastava || Rajesh Thombre || Subroto Dutt
Page No. :: 24-29

In this paper, a review is made on the geometry and working of a box type solar cooker, to assess the performance of SBC's, considering work of few researchers on the basis of figure of merits. As the efficiency of box type cooker is highest due to low heat losses and greenhouse effect by providing glass cover and economically cheaper, hence appropriate for rural people. SBC design referring geographical and climatic-conditions may make them more user friendly in today's context. It is observed that the design, construction and geometry of SBC play an important role in enhancing its performance. In the reviewed literatures, variety of tests for evaluating the thermal performance of SBC such as the utilizable efficiency, cooking power and figure of merits have done and tested.

Keywords: Solar Box Cooker , cooking, Figure of Merits , green house effect , Utilizable efficiency, cooking power

[1]. L. R. Fagbenle, "Estimation of total solar radiation in Nigeria using meteorological data", Journal of Renewable Energy, vol.1, no.1, 1990, pp.1–100.
[2]. Sample registration system baseline survey 2014 of Ministry of home affairs.
[3]. J.F. Kreider and F. Kreth, "Solar heating and cooking (active and passive design)", Hemisphere Publishing Corporation, Washington, DC, USA, 2003.
[4]. Dr.S. Waseem A.Ashraf, Safia Khanam and ayaz ahmad,‗"Effects of indoor air pollution on human health: A micro level study of Aligarh city-India", Merit research journal of education and review, Vol. 1(6), july 2013, pp. 139-146.
[5]. Debosree ghosh and pratap parida, "Air pollution and India:Current scenario", International journal of Current Research, Vol.7, Isssue 11, Nov. 2015, pp.22194-22196


Paper Type :: Research Paper
Title :: Iot Based Automatic Street Light System
Country :: India
Authors :: Rohan Ekatpure || Shubham Khandagle || Ganesh Bhande || Vijay Sawant
Page No. :: 30-37

This paper aims for coming up with and execution the advanced development in net systems for energy saving of street lights. Currently we've got a manual system wherever the road lights are going to be switched ON within the evening before the sunsets and that they square measure shifted within the next day morning after there is sufficient light on the outside. But the particular temporal order for these lights to be switched ON is once there's absolute darkness. With this, the facility is going to be wasted up to some extent. This paper gives solution for electrical power wastage. Also the manual operation of the lighting system is totally eliminated. The papered system give an answer for energy saving.............

Keywords: PIC Microcontroller, IR Sensor, Current Sensor, LDR, Intel Galileo Gen2.

[1]. Subhas Chandra Mukhopadhyay, Fellow, "Wearable Sensors for Human Activity Monitoring: A Review" IEEE Sensors journal, vol. 15, no. 3, march 2015 1321.
[2]. Matthew Kane, Amy kesluk, Edward Teawetal., "A Wireless Health Monitoring System," in Proc .IEEE, 2005.
[3]. Takuji Suzuki, Hirokazu Tanaka, Shigenobu Minami etal., "Wearable Wireless Vital Monitoring Technology for Smart Health Care." 7th International Symposium on Medical Information and Communication Technology (2013).
[4]. Archana. G, Aishwarya N, Anitha J "Intelligent Street Light System" International Journal of Recent Advances in Engineering & Technology, Vol-3, Issue-4, 2015.
[5]. AkshayBalachandran, Murali Siva, V. Parthasarathi, Surya and Shriram K. Vasudevan "An Innovation in the Field of Street Lighting System with Cost and Energy Efficiency"Indian Journal of Science and Technology,Vol-8, August 2015.


Paper Type :: Research Paper
Title :: On Load Fault Detection of Im Using Microcontroller
Country :: India
Authors :: Ashish Porkute || Siddhesh Patil || Lalit Gawande || Sagar Kurve || Mohammad Sohail
Page No. :: 38-43

In working AC Induction motor problems that arise are common nowadays. The main aim of this project is to detect faults of three phases IM and control the faults. The three phase induction motor may experience many incipient faults due to various reasons. So the protection of these motors from such faults is very important. The various faults are over-voltage/current, under-voltage/current, overload, single phasing, over-temperature etc. The most important parameters are voltage, current, and temperature. Here a new protection method is implemented, which is low cost and reliable. The fault that occurs normally in the motor are high temperature, over load, over voltage/current, under voltage/current etc..............

Keywords: Microcontroller PIC16f886, Induction Motor, temperature sensor

[1]. Microcontroller based fault detection and protection system for induction motor. ICICCS-2017
[2]. Fault analysis of induction motor fed by a fault tolerant voltage source inverter (IEEE) ICCEET-2012
[3]. Fault Detection and Protection of Induction Motor Using Fuzzy Logic ICIEEIMT 17
[4]. Online Unbalanced Rotor Fault Detection of an IM Drive Based on Both Time and Frequency Domain Analyses. 2015 IEEE
[5]. Detection and Diagnosis of Faults in Induction Motor Using an Improved Artificial Ant Clustering Technique. IEEE 2013
[6]. Fault Detection and Correction of 3-phase Induction Motor (IJARECE) Volume 3, Issue 8, and August 2014


Paper Type :: Research Paper
Title :: Smart Technology for Classroom
Country :: India
Authors :: Amita A. Narnaware || Kailas R. Londhe || Karishma J. Atram || Priyanka S. Dabhade || Sonu T. Thenge || Vivek V. Pawar || Atul s. Lilhare
Page No. :: 44-48

The aim of proposed work is to develop a smart technology for classrooms in schools, colleges etc. In this project work Arduino UNO is used for programming in designing of smart control technology where PIR sensor , LDR ,Finger print sensor, LCD display , Temperature sensor are used for human identification, light intensity , attendance in person and display purpose. The overall scenario is design in order to enhance the power utilization by reducing energy consumption. Also at the same time it has been seen that while taking attendance, there is a break in continuity of teaching during traditional condition. So this can be avoided by providing smart attendance monitoring, that care is taken through this project.

Keyword: Arduino, LCD display, Relay driver circuit, LDR,PIR sensor, LM35 sensor, finger print sensor, Opto coupler.

[1]. http://www.rashmondal.info/IR-object-detection.
[2]. http://www.ijret.org.
[3]. The 8051microcontroller and embedded systems: MUHAMMAD ALI MAZIDI. [4]. http://www.resistorguide.com/photoresistor/


Paper Type :: Research Paper
Title :: Bladeless Wind Turbine
Country :: India
Authors :: Dr. Ravindra. M. Moharil || Animesh Khairkar || Ambika Kulkarni || Niharika Yedekar || Shubham Badure || Shubham Bawaskar
Page No. :: 49-52

In this project we are focusing on generating electrical power .We know the need of Non-conventional energy system at this time to our country. The power is generated by the piezo-electric arrangement is fitted in the blade less wind mill. It is a new wind energy technology specially designed for on-site generation on residential areas, being able to work on grid, off grid, or along regular solar panels or other generators. Compared to traditional wind turbine the cost of bladeless wind turbine is very less as well as cost required for installation is very less.

[1]. International Journal Of Pure and Applied Research In Engineering and Technology,"Vortex Bladeless: A New Paradigm Wind Mill",Pune,Maharashtra,India,2017
[2]. Saurav Bobde,Sameer Jadhav, Study of Vortex Induced Vibrations for Harvesting Energy; IJIRST – International Journal for Innovative Research in Science & Technology| Volume 2 | Issue 11 | April 2016
[3]. IJIRST –International Journal for Innovative Research in Science & Technology| Volume 2 | Issue 11|april'16
[4]. Prof. Harshith K, Blayan Santhosh Fernandes Shreerama P, R Thilak Raj Bladeless Wind Power Generation. Paper No. (IJSRD 2321-0613 Vol.4.Issue 03, 2016)


Paper Type :: Research Paper
Title :: Dual-axis solar tracker, a case study
Country :: India
Authors :: Shailesh Bhoyar || Pradip Bodke || Shubham Ramteke || Aarti Bodkhe || Avinash Gadpayle || Swati dewase || Mahadeo Gaidhane
Page No. :: 54-59

Renewable energy resources become very popular and commonly used now a days. The main purpose of this project is to be overcome the issues of energy crisis in today's World. To overcome this we used renewable energy resources manifold. This project deals with Techno-Economical study of solar static and dual axis tracker. The contest in converting sunlight to electricity via photovoltaic (PV) solar cell. Solar tracker superiority over stand still or single axis tracker to improve the quality of efficiency of the solar cell. Energy generation basically required huge starting investment. The outcome of the solar tracking system has analysed and compared with fixed solar panel and found better performance in terms of power and economically beneficial . Hence according to case study tracking system the Photovoltaic (PV)Panel are able to receive maximum sunlight that generate more energg

Key Words: Solar panel ,Solar tracking ,Microcontroller ,Renewable energy

[1]. Seyad Samsamoddin, " Econometric analysis of solar tracker system in India,a case study''vol .10,No.44.
[2]. Amit Chakraborty Chhoton, "Dual Axis Solar Tracking System-A Comprehensive Study".
[3]. Cheema, Sukhraj Singh. "Simulation studies on dual axis solar. photovoltaic panel tracking system." PhD diss., T hapar University Patiala,2012 425
[4]. S.Shanmugam and W.Christraj, " The Tracking of the Sun for Solar Paraboloidal Dish Concentrators",ASME Transactions,Vol.127,feb2005.
[5]. Data provide by Lokmat press industry using solar power ,buttibori ,Maharastra 441122.